These boards provide two complementary outputs
when the set point is tripped & the LED illuminates: Lo
and
Hi (Gnd and +12V) for use with any system. Requires a 7-12VDC
Power source.
 |
.
AV2-1 Input board changes state
on any adjustable Audio or Video level. The unit senses the outputs
from any source for reporting the mode of that equipment.
This is especially helpful for low-power VCRs that do not
have other means of feeding back an On/Off status, and for Audio
equipment that puts out a minimal line level signal.
|
|
|
CS2-1 Input board changes
state on an adjustable AC current level (5W to 2000W). This board
uses a new, patent pending non-contact current sensor which is
double insulated for safety.
The AC line cord is simply routed over the board-mounted sensor;
this allows it to check the On/Off status for any gear that has
greater than a 25% difference between its On and Off state current
draw
|
 |
FB2-1 Input board changes state
on an adjustable level of magnetic energy as is found around
a TV or computer CRT monitor. This unit mounts near any target
device for non-contact sensing and reports its On/Off status
for use in conditional command sequences.
This feature is especially helpful in equipment with "toggle"
power On/Off commands as it allows the determination of the actual
state.
|
 |
LS2-1 Input board changes state
on any adjustable light level. The stick-on sensor head can monitor
the light level from dim panel LEDs for reporting the mode of
equipment.
This same unit can also be used to measure sunlight level
for opening or closing drapes or for heating/cooling setpoint
changes in your energy management system.
|
 |
TS2-1 Input board changes state
on any adjustable temperature level. The plug-in sensor can monitor
the temperature of any device for reporting the mode of equipment,
or can be used as a freeze alarm or on any other temperature-dependent
condition. |
 |
VS2-1 changes state on any adjustable
Voltage level. This allows the sensing of non-standard gear or
equipment that has, or can be modified to provide, a voltage
that changes Status for monitoring.
The unit has a high impedance input which senses a differential
voltage (0.5 to 50V floating up to 100V) from any source for
reporting the mode of that equipment.
|
 |
MR1 Super Sensitive IR Receiver
& Repeater with 3 - 40 ft adjustable range. IR modulation
frequencies up to 125kHz are reliably detected and decoded.
It plugs directly into IR MASTER, BO1, or SWP
as an additional remote input, or it may be used with an IR Emitter
as a stand-alone repeater to send all IR commands between rooms
(0.6" x 0.4" x 2").
|
 |
EM1 "Stick on" InfraRed
emitter, for direct mounting over the IR receive window of any
gear with an IR remote..
EM2 "Stick on" InfraRed
emitter similar to EM1 but with a red LED indicator that signals
when an IR command is being sent
DM1 is a stick-on Emitter with
two "heads that allow 2 different Units to be controlled
from the same IR Output jack.
|
|
|
BL3 This IR blaster will wire
to any IR output channel. It transmits high power pulses to any
IR gear within its line of sight to 30 ft, ±45°. As
with all of our accessories this blaster and its connections
are Xantech compatible. This unit will faithfully reproduce any
IR waveform up to 2Mhz and accommodates the Pioneer Elite and
the Bang & Olufsen Commands.
Requires a 9V power source, and IR signal from an IR MASTER,
BO1, SWP or any other system.
|
 |
IRV InfraRed Verifier
gives a quick and easy, audible translation of the IR pulse stream
energy emitted from any IR source (IR Remotes, EM1 emitters,
etc). The audio output gives a clear indication of both signal
strength and command integrity. Detects up to 6"; 9V battery
lasts over 1 year. |
