Dancraft Enterprises Order Form

Dancraft Enterprises

Universal Accessories

Order Information

We are currently accepting orders by fax, phone, company PO or credit card (MasterCard and VISA). Please complete either the Word or PDF order forms (to the right) and fax or e-mail your order to us.

THANKS!

For quantity pricing, please contact us.

To place an order, click on the appropriate order form below:

>MS Word format (edit and email back)

>PDF format (print and fax back)

E-mail any ordering questions to:

sales@dancraft.com

or call 1-310-643-8782
9:00am - 5:00pm PST

Infrared Accessories for Automation Systems by Dancraft or other

EM1 14 IR "Stick-on" emitter, on 6 foot cable to 1/8" jack for direct control of IR gear.

EM2 16 IR "Stick-on" emitter as above, with LED that flashes as IR commands are sent.

DM1 18 Dual "Stick on emitter". Allows the same output to be connected to 2 sensing eyes.

BL3 69 IR Blaster for flooding an area with IR Commands as high as 2MHz in carrier frequency. Requires 9Vdc

MR1 99 Super Sensitive IR Receiver w/ adjustable gain.

IRV 39 InfraRed energy Verifier gives an audible translation of any nearby IR pulse stream.

X10 Power Line Accessories for Automation Systems by Dancraft or other

TW523 $24 X10 Power line interface between Cybermate and your homes AC wiring to allow Home Pilot to control the lighting in your home.

XPH 69 Phase Coupler communicates X10 signals across both 110V sides of house wiring.

X10 Modules Call Full line of X10 Power Line Modules. Contact Dancraft

Status Sensors are stand alone and will work with anybody's automation system. They provide two complementary outputs when the set point is tripped & the LED illuminates: Lo and Hi (Gnd and +12V) for use with any system, and require a 7-12VDC Power source.

Model # Price Description

AV2-1 149 AV2 changes state on any adjustable Audio or Video level. The unit senses the output from any source for reporting the mode of that equipment. With adjustable Delay pot.

CS2-1
149
CS2 changes state on an adjustable AC current level (10W to 2000W). It uses a non-contact current sensor next to the line cord to monitor current in the wire.

FB2-1
149
FB2 changes state on an adjustable level of magnetic energy as is found around a TV or computer CRT monitor. It mounts near any target device for non-contact sensing. This feature is especially helpful in gear with "toggle" On/Off commands.

LS2-1 149 LS2 changes state on any adjustable light level. The stick-on sensor head monitors the light level from panel LEDs for reporting the mode of equipment. It can also measure sunlight level for opening or closing drapes.

TS2-1 149 TS2 changes state on any adjustable temperature level. The remote sensor head monitors the local temperature of the equipment.

VS2-1 149 VS2 changes state on any adjustable Voltage level. The unit senses a differential voltage (5 to 50V floating up to 100V) from any source for reporting the mode of that equipment.

Return Home

EM1	14	IR "Stick-on" emitter, on 6 foot cable to 1/8" jack for direct control of IR gear.
EM2	16	IR "Stick-on" emitter as above, with LED that flashes as IR commands are sent.
DM1	18	Dual "Stick on emitter". Allows the same output to be connected to 2 sensing eyes.
BL3	69	IR Blaster for flooding an area with IR Commands as high as 2MHz in carrier frequency. Requires 9Vdc
MR1	99	Super Sensitive IR Receiver w/ adjustable gain.
IRV	39	InfraRed energy Verifier gives an audible translation of any nearby IR pulse stream.

TW523	$24	X10 Power line interface between Cybermate and your homes AC wiring to allow Home Pilot to control the lighting in your home.
XPH	69	Phase Coupler communicates X10 signals across both 110V sides of house wiring.
X10 Modules	Call	Full line of X10 Power Line Modules. Contact Dancraft

Model #	Price	Description
AV2-1	149	AV2 changes state on any adjustable Audio or Video level. The unit senses the output from any source for reporting the mode of that equipment. With adjustable Delay pot.
CS2-1	149	CS2 changes state on an adjustable AC current level (10W to 2000W). It uses a non-contact current sensor next to the line cord to monitor current in the wire.
FB2-1	149	FB2 changes state on an adjustable level of magnetic energy as is found around a TV or computer CRT monitor. It mounts near any target device for non-contact sensing. This feature is especially helpful in gear with "toggle" On/Off commands.
LS2-1	149	LS2 changes state on any adjustable light level. The stick-on sensor head monitors the light level from panel LEDs for reporting the mode of equipment. It can also measure sunlight level for opening or closing drapes.
TS2-1	149	TS2 changes state on any adjustable temperature level. The remote sensor head monitors the local temperature of the equipment.
VS2-1	149	VS2 changes state on any adjustable Voltage level. The unit senses a differential voltage (5 to 50V floating up to 100V) from any source for reporting the mode of that equipment.